LEDS: Status indicators
Below are short explanations of the DSL status lights of some modems used by Westco / Miller / Zenda / Communications Plus customers:
Westell
Wirespeed 2110 / 2200
|
| LED | State | Description |
| POWER | Solid Green | Power ON |
| No Light | No Power | |
| READY | Slow Flashing | Power ON and passed power-up diagnostics (1 flash/sec) |
| Moderate Flashing Green | Power ON and attempting synchronization (2 flashes/sec) | |
| Steady Green | Power ON and synchronized with ADSL line card | |
| Steady Red | Hardware power-up in progress | |
| Blinking Red | Unit failed power-up diagnostic | |
| Alternating Red/Green | Modem Diagnostics failed | |
| No Light | No Power | |
| ETHERNET | Solid Green | Ethernet link established |
| Flashing Green | Transmit or Receive Activity | |
| No Light | No link established | |
| USB | Solid Green | USB link established |
| Flashing Green | Transmit or Receive Activity | |
| No Light | No USB link established |
Paradyne
6211
| LED | State | Description |
| PWR | ON | Modem has power |
| OFF | There is no power | |
| Status | ON | Modem is functioning properly |
| BLINKING | Modem is rebooting. | |
| OFF | Modem is not ready or has malfunctioned. | |
| LAN | ON | Modem has a successful 100Mb Ethernet connection. |
| OFF | Modem has a successful 10Mb Ethernet connection | |
| Activity | ON | Modem has a successful Ethernet connection. |
| BLINKING | Data is being sent or received. | |
| OFF | Modem is not ready or malfunctioned. | |
| USB | ON | USB link established |
| OFF | No USB link established |
D-Link
DSL-302G
| LED | State | Description |
| POWER | ON | Modem has power |
| OFF | There is no power | |
| STATUS | ON | Modem is functioning properly |
| OFF | Modem is not ready or has malfunctioned. | |
| ADSL | ON | Trying to connect ADSL line |
| OFF | ADSL line is linked | |
| ETHERNET | ON | Modem has a successful 100Mb Ethernet connection. |
| OFF | Modem has a successful 10Mb Ethernet connection | |
| USB | ON | USB link established |
| OFF | No USB link established |
Speedstream
5260
| LED | State | Description |
| sys |
Off |
Modem power off. |
|
Red |
The modem is unable to connect to Westco Online. Check the System Status to determine if you can resolve the issue. |
|
|
Yellow |
The modem is attempting to connect to Westco Online. |
|
|
Green |
The modem power is on. Look at the other lights to troubleshoot connectivity issues. |
|
| atm |
Off |
Modem power off. Either turn it on and try to re-connect or follow these steps to troubleshoot the connection issue. |
|
Red |
This indicates a communication failure. Check the System Status. |
|
|
Green (blinking) |
This indicates a communication problem. Follow these steps to troubleshoot the connection issue. |
|
|
Green (solid) |
Modem is ready to communicate. Try some other troubleshooting steps if you are unable to connect. |
|
| dsl |
Off |
Either turn it on and try to re-connect or follow these steps to troubleshoot the connection issue. |
|
Red |
This indicates a configuration failure. Check your DSL software configuration or your LAN settings. |
|
|
Yellow |
This indicates a communication problem. Troubleshoot the connection. |
|
|
Blinking green/yellow |
The modem is attempting to connect to Westco Online. |
|
|
Blinking green |
The modem is attempting to connect to Westco Online. |
|
|
Green |
The modem and Westco Online are connected and the data is transmitting at a normal rate. |
|
| enet |
Off |
An Ethernet link was not detected. Verify your NIC connection. |
|
Red |
This indicates a communication failure. |
|
|
Blinking green |
Ethernet traffic flow is normal. |
|
|
Green |
Ethernet ready. |
VisonNet
200ES
| LED | State | Description |
| ADSL | Flashing | Trying to connect ADSL line |
| Solid | ADSL line is linked | |
| Tx/Rx | Off | No DSL detected |
| Off | Not sync'd | |
| LAN | ||
| Green | Sync'd with full speed connection | |
| ACTIVITY | Flashing | The device is ready to work |
| POWER | Solid | Input power is applied |
| Off | Power Off |
